Archee Studio.

00Arrive

Carry the work to the drawing.

Agentic tools for mechanical design. A brief arrives as a page; it leaves as drawings, the record behind them, and the report that agrees with both.

Start a project See the sheet

01Commit

Every number, written once.

A machine-readable record holds every value. The drawing, the parts list and the report are read out of it, so nothing is typed twice.

The AgentCAD run loop: brief, solve, draw, report, then verify on the return path, with a dashed revision route from verify back to solve. A crew of three works the loop: one on the brief, one on the drawing, and one in the middle of the record. ABCDEFGH 1234 EVERY VALUE FROM ONE RECORD ON MISMATCH · REVISE A CREW, AT WORK 01 BRIEF assignment + variant 02 SOLVE one design record 03 DRAW the drawing itself 04 REPORT written, sourced 05 VERIFY reopen and compare RUN REVISION THE AGENT LOOP SHEET 01/05 ARCHEE STUDIO SCALE 1:1 DRAWN BY agent REV A The AgentCAD run loop: brief, solve, draw, report, verify, then back to the start. BRIEF assignment + variant SOLVE one design record DRAW the drawing itself REPORT written, sourced VERIFY reopen and compare THE AGENT LOOP ARCHEE STUDIO SHEET 01/05 · REV A
Fig. 01 · the loop, drawn to scale 1:1 one record · five stations · one gate

One source, so nothing can quietly disagree.

02Draw

AgentCAD draws the sheet.

Not generated from a prompt and hoped for. Drawn object by object out of the record: lines, arcs and dimensions, not a picture of them.

Takes · one brief
Returns · drawings, report, record
Status · private beta

An A3 detail sheet for the output shaft: six steps with diameter callouts and fits, a length chain of six dimensions, a section through the keyway, a fits table and a title block. ABCD 123 A Ø28 k6 Ø35 k6 Ø42 Ø40 k6 Ø35 k6 Ø28 h8 70100301409080 510 SECTION A–A KEYWAY 12 N9 NOTES 1 · ALL DIMENSIONS IN MILLIMETRES 2 · GEAR SEAT Ø40 k6 · BEARING SEATS Ø35 k6 3 · BREAK SHARP EDGES 0.5 × 45° FEATURE FIT NOTE GEAR SEAT Ø40 k6 KEY 12 N9 BEARING A Ø35 k6 Ra 0.8 BEARING B Ø35 k6 Ra 0.8 COUPLING Ø28 h8 — KEYWAY 12 N9 × 5 DEPTH 5 OUTPUT SHAFT · DETAIL A3-02 PROBLEM 05 / VARIANT 01 SCALE 1:2 DRAWN BY agent · 2026-10 REV A CHECKED · archee.studio
Fig. 02 · the detail sheet, drawn to scale 1:2 output shaft · rev A
01

Engineering, not autocomplete

Motor and ratio allocation, two gear stages, shaft forces, bearing life, fits — each with a substitution you can check.

02

Editable output

Real drawing objects, not an exported picture of one.

03

Verification before claims

The finished file is reopened and compared; a mismatch fails the run.

Then the sheet has to survive being reopened.

03Check

Then the sheet is checked.

The drawing is reopened and compared with the record and the report. A mismatch fails the run; a summary is not evidence.

The design record gives a diameter of 180.00; the reopened sheet measures 180.20. The difference is 0.20 and the gate fails. Below, the agent summary says pass and is struck out. THE RECORD DIAMETER d₂ 180.00 THE SHEET · REOPENED MEASURED d₂ 180.20 Δ 0.20 FAIL AGENT SUMMARY · PASS ARTEFACT · FAIL THE RUN STOPS HERE
Fig. 03 · the check, drawn to scale 1:1 record · sheet · gate
Example run · problem 05 / variant 01 complete
  1. read brief, variant, constraints ok
  2. solve ratio, shafts, bearings, fits ok
  3. draw assembly, detail sheet ok
  4. write report, from the same record ok
  5. verify reopen, compare, fail on mismatch pass
Assembly drawing · the machine, assembled
Detail drawing · one part, toleranced
Report · the calculation, shown
Record · behind all three

Sample pack on request. Client work stays private until the client says otherwise.

What is left is a pack someone can review.

04Sign

A small team signs it.

Narrow on purpose: mechanical design automation, the files engineering teams actually review, and the checks that make those files trustworthy.

01

What we take on

Machine design and power transmission: reducers, drives, and the drawings and report that ship with them.

02

What we sign

The sheet, the record and the report — or none of them.

03

What we refuse

A drawing nobody can verify, and a summary standing in for the artefact.

A sign-off block with three rows: stamped by the agent, initialled by a hand, and still unsigned. A dotted trail leaves the block for the next brief. SIGN-OFF DRAWN CHECKED lt. APPROVED UNSIGNED BRIEF 06 NEXT BRIEF
Fig. 04 · the sign-off, drawn to scale 1:1 one brief out · one brief in

Your agent, your model, the CAD you already own.

Which leaves one thing: the next brief.

05Return

Send the first page.

A brief is enough to start: what has to be drawn, in which application, and by when. We say plainly whether it is a fit before anyone signs anything.

or

hello@archee.studio

Reply within two working days